The Tektronix HFS9DG2 is a data time generator card.
Features
- Complete Stimulus Setup in Just Minutes
- Specify Data and Timing on Every Pin
- Up to 630 MHz Repetition Rate
- Fully Digital Implementation
- Multi-channel Architecture
- Up to 640 or More Phase-locked Channels
- Independent Edge Placement
- Channel Deskew
- Precision Channel-to-channel Timing Alignment
- 1 ps Timing Resolution
- GPIB (IEEE 488) Programmable
- Modular Construction
- Upgrade Capability
- Maximum Control and Flexibility
Applications
- Characterize CMOS, ECL, ACL, BiCMOS and GaAs Devices
- Precise Clock Source
HFS9000 Stimulus System
When product designs were simple, and time-to-market not so critical,
designers could afford the days, or even weeks, necessary to assemble, program,
debug and characterize the various elements of a stimulus system and its
fixturing. As product design complexity and market pressures have increased,
however, designers of high-speed, high-performance circuits simply cannot afford
this expenditure in time.
Now there's a solution. With Tektronix HFS9000 Stimulus Systems we've taken
the features of a high-performance pulse generator, made them better and added
complete data generation capabilities as well. We've eliminated the need for a
switch matrix since we have data and timing on every pin. And the need for a
separate power supply is gone, as the HFS9000 has the ability to produce the DC
levels needed to drive logic lines directly. Finally, all these capabilities are
present on every pin simultaneously, so you get extremely flexible formatting.
Now you can set up a complete stimulus system in minutes, rather than hours or
days, and test products more thoroughly throughout the development cycle.
Digital Architecture
The HFS9000 Series products were designed as completely programmable digital
instruments rather than being based on traditional monostable analog
architecture. This allows more capability and flexibility in pulse edge
placement without the restrictions that analog instruments commonly impose. Now
you can adjust both Delay and Width from 0 to 20 Micros over all frequencies.
Modular Design
You can build a stimulus system with from four to 36 channels in one
mainframe, and 640 or more channels across multiple phase-locked mainframes.
Choose from the HFS9003 mainframe with 3-slot, 12-Channel capability, or the
HFS9009 mainframe with 9-slot, 36-Channel capability. Both systems can include
the 4-Channel HFS9DG1 and HFS9DG2 Data Time Generator cards in any combination.
All channels are slaved to a common clock, resulting in highly accurate
channel-to-channel edge placement. This makes the HFS9000 ideal for precise
characterization and evaluation of synchronous devices having multiple, and
possibly interactive, inputs.
Full Channel Deskew Capability
All HFS9000 channels have independent, wide deskew ranges to allow precise
pulse alignment and timing at the device under test (DUT). Deskew compensates
for the timing differences caused by cabling and fixturing so your analysis can
be focused on the relative timing at the DUT.
1 ps Timing Resolution
No other system lets you generate whatever combination of signals is
required, with data and timing on every pin with 1 ps resolution. Now you
can create data buses, clocks, strobes, gated clocks, logic level sources, pseudorandom
bits and other stimuli with unequaled accuracy. You can perform setup and hold
time margin tests by providing the clock, data, set and reset signals to the DUT.
And you can hold inactive signals at programmable high or low logic levels,
eliminating the need for external DC voltage sources and microwave switches.
630 MHz Repetition Rate
Accurate and repeatable AC measurements of prop delay, setup and hold time,
and maximum operating frequency (fmax) require fast rep rates and edge speeds.
With repetition rates up to 630 MHz, the HFS9000 is ideal for
characterizing the most advanced logic families, and it can be used for testing
component compliance with the SONET telecommunications standard. Transition
times as fast as 250 ps (20%-80%) enable repeatable and accurate testing of
the highest-speed ECL and GaAs digital devices. Variable transition time
control from 800 ps to 6 ns is also available with the appropriate
output levels for testing advanced CMOS, BiCMOS and TTL logic families.
Easy Editing of Setups and Vectors
Edit setups and vectors easily with BitWriter software. With this Microsoft
Windows based package you can build a complete test setup, including timing
parameters, voltage levels, channel assignment and test vectors on your PC -
ideal for remote test development. Individual setups and test vectors can be
uploaded and stored when the HFS9000 has multiple users.
Fully Programmable
Programmability is important in developing automated, repeatable tests in
R&D, incoming inspection and production of high-speed components. Therefore,
the HFS9000 offers full implementation of the IEEE 488.2 standard and utilizes
Tektronix Codes and Formats. GPIB/RS-232 ports provide for remote, fully
programmable control. Coupled with a high-speed acquisition system, such as the
TDS694D DSO, 11801B Digital Sampling Oscilloscope, or the most advanced logic
analysis system on the market - the Tektronix TLA700, a fully automated test
system can be developed with unequaled accuracy and repeatability.
Phase Lock Mode
Phase lock-in allows the internal time base to be phase-locked to an external
frequency source. This "supercharger" capability can be used to
augment the speed performance of automated component test systems by creating
synchronized signals as fast as 630 MHz.
- 制造商: Rohde Schwarz
- 模型: HFS9DG2
