California Instruments 2003RP AC Power Source
Programmable AC Power Source 2000VA
Compact AC Power
Offering simple rotary front panel controls, the 2003RP Programmable AC Power
Source is ideally suited for a wide range of three phase applications.
Selectable input voltage ranges allow this product to be used anywhere in the
world to provide a convenient source of variable utility power for the testing
and evaluation of domestic and commercial equipment. All common line voltage and
frequency combinations are covered. In addition, the frequency range extends to
5,000 Hz, making these products ideal for commercial and defense avionics
applications. Accurate measurement functions are available as an option to
eliminate the need for external test equipment in many test setups. Voltage,
current, peak current, power, and power factor can be read directly on the large
LCD display or over the bus. Overload protection is provided standard using a
programmable current limit function.
Easy To Use Controls
Front panel digital rotary encoders are used to set voltage and frequency. These
controls have an analog feel, with the precision and reliability of digital
circuits. Settings are read directly on the large high contrast LCD displays.
Dual output voltage ranges of 135 Vrms and 270 Vrms L-N, provide maximum current
at the required voltage. The output frequency can be varied from 16 Hz up to
5,000 Hz to cover commercial, avionics and defense power applications.
IEC 1000-3-2 Test Applications
The low total harmonic distortion of the output makes the RP Series suitable AC
sources for IEC 1000-3-2 Current Harmonics pre compliance testing.
Quality Control
For product quality test applications, the 2003RP can be used to simulate
line conditions found anywhere in the world. This ensures products destined for
export will operate as designed.
Avionics Applications
As an affordable and reliable source of 400 Hz AC power, the 2003RP is well
suited for commercial and defense avionics applications.
Functional Design
The small form factor and low weight of these units make them convenient to use
in a variety of locations. Removable rubber feet protect the work surface if the
unit is used in a bench top mode. The 3.5 inch height saves valuable rack space
when compared to conventional AC power sources at this power level.
Remote or Local Operation
For automated test equipment (ATE) applications, the 2003RP can be outfitted
with both GPIB and RS-232C using the -IF option. A front panel lock out mode is
supported on both models if operator interaction with the AC source is not
required or desired.
The optional remote control interface allows complete control of all AC
source functions and provides measurement data to the controller. This allows
the RP Series AC source to be used as a low cost AC test system. A Windows
Graphical User Interface (GUI) program is included with the interface option.
Automatic power cycling and transient generation is made possible with the use
of this GUI program. The GUI output control, measurement and transient screens
are shown here. For quality assurance applications, measured voltage, current
and VA readings can be logged to disk for documentation and analysis purposes.
All data recorded is time stamped to create a complete history of each test run.
Up to eight often used front-panel setups can be stored in non-volatile memory
for quick recall from the PC controller through the interface. With enhanced
capabilities such as data logging to file and Dynamic Data Exchange to other
Windows programs, many applications can be addressed without the need for
writing custom code.
Extensive Transient Control
With the addition of the remote control interface option, the 2003RP is capable
of producing transients with a high degree of user programmability. Setting up
transient programs is facilitated by a Windows Graphical User Interface program
that allows amplitude, frequency and event duration to be programmed from a PC.
Time resolution is 1 ms (0.001 sec) with a minimum time interval ranging from 10
to 40 ms, depending on the transient type. Transient programming allows the
effects of common line disturbances such as voltage surges, sags, drop-outs and
frequency fluctuations on the unit under test to be evaluated. Voltage drop out
transients can be programmed at random phase angles or at 0, 90, 180 and 270
degrees with respect to phase A.
AC Line Immunity Testing
Special application support is provided for pre-compliance IEC 1000-4 immunity
testing, specifically IEC 1000-4-11 Voltage Dips and Interruptions, IEC
1000-4-14 Voltage Fluctuations (draft) and IEC 1000-4-28 Frequency Variations
(draft). All IEC test windows provide on screen editing of test parameters to
meet various product category test requirements. These test sequences can be
saved to disk, enabling a library of IEC test sequences to be created. Generic
test files are supplied with the program for immediate use. After a test run, a
complete test report including the user provided equipment under test data and
test parameters used can be printed or saved to disk.
Features:
- 16 Hz to 5,000 Hz
- Three phase output (875 VA per phase)
- Dual output voltage ranges, 0-270 or 135 VAC
- Full power with up to 3:1 crest factor loads
- Standard Current measurement
- Optional measurements for Peak Current, Voltage, Real Power, Apparent
Power, Power Factor
- Simple Front Panel and Rear panel Connections
- Optional GPIB and RS-232C interfaces
- Made in USA
- CE Mark
- 制造商: California Instruments
- 模型: 2003RP-0P1
