General Power Supplies : Philips PM2811

此产品是工厂翻新

Philips PM2811
放大图片Philips PM2811

Call 1-800-615-8378 for more information

Request a Quote

Check Rental Availability

租赁测试设备


The Fluke Philips PM2811 is a Single Output DC Power Supply with the following specifications:

  • OUTPUT module 30 V - 10 A - 60 W
    • Output Voltage range 0 to 30 V
    • Output Current range 0 to 10 A
    • Output Power 60 W
    • Overvoltage protection range 2 to 32 V
  • Accuracy (at calibration temperature)
    • Output Voltage +/- 0.04 % of setting + 10 mV
    • Output Current +/- 0.1 % of setting + 50 mA
    • Over Voltage Protection +/- 0.5 % of setting + 150 mV
  • Temperature coefficient
    • Output Voltage (0.016 % of setting + 2 mV)/K
    • Output Current (0.05 % of setting + 2 mA)/K
  • Long term drift (in an 8 hour period)
    • Output Voltage 0.04 % of setting + 5 mV
    • Output Current 0.05 % of setting + 10 mA
  • Programming Resolution (12bit)
    • Output Voltage 7.5 mV/LSB
    • Output Current 2.5 mA/LSB
    • Over Voltage Protection 7.5 mV/LSB
  • Source Effect (for any line voltage change within rating)
    • Voltage +/- (0.01 % of setting + 2 mV)
    • Current +/- (0.02 % of setting + 2 mA)
  • Load Effect (load change 10 % to 90 % or 90 % to 10 % full load)
    • Constant Voltage +/- (0.01 % of setting + 5 mV)
    • Constant Current +/- (0.02 % of setting + 5 mA)
  • Load cross regulation Negligible for both voltage and current
  • Output Noise (PARD)
    • Constant Voltage pp/rms 15 mV/3 mV
    • Constant Current rms 10 mA
    • Switching Frequency approx. 20 kHz approx.
  • READBACK ACCURACY:(referred to the output terminals)
  • Accuracy (at calibration temperature)
    • Voltage +/- (0.05 % + 25 mV)
    • Current +/- (0.1 % + 30 mA)
  • Measuring Resolution (12 bit)
    • Voltage resolution to interface 7.5 mV
    • Current resolution to interface 2.5 mA
    • Voltage resolution to display 10 mV
    • Current resolution to display 10 mA
    • Max. Current at Reverse voltage 10 A
    • REMOTE SENSE > 0.25 Volt drop per lead (at open sense connections, the output voltage will not be more than 3 V above the programmed value)
    • DYNAMIC OPERATION I=1 A between 1 and 10A between 0.5 and 5A between 1 and 10A
      • Settling band +/- 50 mV
      • dI/dt < 1 A/?s
      • Overshoot < 150 mV
      • Recovery time < 1 ms
    • Programming response (measured with resistive load)
    • Up (0 V to max. output) 100 ms @ 2 A
    • Up (0 V to max. output) 50 ms @ (no load)
    • Down (max.output to 1 V) 100 ms @ 2 A
    • Down (max.output to 1 V) 50 ms @ (no load)
  • Reprogramming delay
    • Range 50 ms to 60 s
    • Resolution 1 ms
    • Default 50 ms
    • Step Interval time up to 60 s
  • 制造商: Philips
  • 模型: PM2811